A remote controlled garage door opener is a convenience and a necessity. With all the benefits to this remote, it only makes sense to get yours from North Shore Commercial Door today. Purchases may be returned for any reason within 30 days. We do not accept returns after 30 days from delivery. Menu Toggle navigation.

Author:Vudosho Megor
Language:English (Spanish)
Published (Last):1 May 2014
PDF File Size:13.24 Mb
ePub File Size:17.15 Mb
Price:Free* [*Free Regsitration Required]

If at any time during the installation process you have questions, please call the Customer Service department at The power cord must be unplugged before attaching any wires. Be sure wire ends do not touch each other or other terminals. If your opener is equipped with a Wireless Keypad or you use other access devices such as a mini-remote control, the batteries must be removed from these devices as well. A Unplug, or open the breaker that supplies power to the garage door opener. B For openers with internal radios.

C For openers with external radios. Attaching the Receiver to the mounting bracket or other metal surfaces could cause interference or grounding. A Cut wire; enough to run from the garage door opener terminal strip to the Receiver.

It may be located on the back, front or sides of the opener or underneath the light lens. B Strip and route wires. Staples driven too tightly can short circuit the wiring. C Wire the receiver. Do not tighten screw yet. Another wire will be added later. D Wire the garage door opener. C Wire the Receiver. D Wire the transformer. Stay away from moving Door and its parts. B Press and release Learn Code Button. D Press the same transmitter button again within 30 seconds to set Code.

Begin programming again at Step B. NOTE: After successfully programming the receiver and all transmitters, engage the garage door. C Press Transmitter button again. The door will stop automatically at the fully open and fully closed positions. A Throw away all old remote controls, wireless keypad, and other access devices.

B For garage door openers with internal radios. Some are thin strips of metal. Some garage door openers have no code switches or punch outs.

C For garage door openers with external radios. If a Transmitter becomes lost or stolen or you want to delete a Transmitter, Wireless Keypad or other access devices:. Take care when opening. Operation is subject to the following two conditions: 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular situation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try and correct the interference by one or more of the following measures: a Re-orient or relocate the receiver antenna, b Increase the separation between the opener and receiver, c Connect the opener into an outlet on a circuit different from that to which the receiver is connected, and d Consult your local dealer.

Any modifications or changes to this equipment which are not expressly approved by the manufacturer could void the user's authority to operate the equipment. Is this compatible with Genie GT? If yes is it easy to change it or has to be done by technician? It will work with the new style Intellicode remote that comes with it, and any other Intellicode remote.

It does come with instructions and is easy to install yourself. Is this compatible with very old systems? I have a Genie opener from and looking to see if it is able to be upgraded. Works great still. I have 2 Moore-O-Matic garage door openers. They were likely installed in or It's a great opener but does not have the safety lasers. I have no remote openers that work. Will this conversion kit work? Can one be used with 2 doors?

We cannot recommend updating any garage door opener without the installed safety beams, this will not work. One conversion kit will not work on two separate garage door openers.

P Model ISD that only works off the wall unit only.. I assume the circuit card bad. The circuit board that controls the remotes would be the R. S control board. You will program each remote separately. Then take the remote, step a few feet away and press and release the button on the remote three to four times. The door will open or close.

Then repeat with the second remote. Will this work with the Silent Max connect model and the several remotes that are already programmed for it? Also, will I need to reprogram my smartphones to use the Alladin remote feature?

This will work with the model. You will have to program the remotes you have into this conversion kit. The Aladdin Connect will not need to be reprogrammed, it will work as normal.

No, this will not work with any garage door opener that does not have safe-t-beams. This will work on any Genie garage door opener that has the Safe-T-Beams attached. I would also like a keypad.

Is there a genie keypad that will work with this system as well. I need a new receiver and a new keypad to open my existing garage door opener. Have a genie G that uses dip switches for programming will this work with it.

Yes, this will change it from the dipswitches to Intellicode technology. The new remote works wonderfully well but I didn't realize the Keyless Entry is not compatible with the older model opener that has dipswitches. Where does the conversion kit mount?

On the Opener or on the ceiling? They will all work with the Universal Conversion Kit. It can be mounted either place. My current receiver connects directly using this connection. Not only does this not work but now the wall button will not work. What am I doing wrong? The original remote stopped working. Will this work with the original Touch N Go??? So frustrating to find replacement remotes. Please help! This conversion kit should not be added to any garage door opener that does not have Safe-T-Beams.

This will work with most Marantec models. Please contact Genie customer service at to confirm your model. You will need to check with LiftMaster on this. It will depend on the garage door opener. Will this work on a genie max blue garage door opener. We have 3 garage doors, each are Genie Blue Max.

We we need to install 3 kits, or just 1? You would need to put a receiver kit on each one if you are trying to make them all have Intellicode technology.

I have a girud-1t and moved it to my new home and the power supply got lost in the move. What voltage does it require and where can I get one? Please contact Genie customer service at We do not sell this online as a separate part. Do I need to set it to codedoger1 or codedoger 2 to program? Thank you, Vincent.


Universal Garage Door Opener Remote Upgrade / Conversion Kit



Genie 36359R Garage Door Opener GIRUD-1T Receiver, Remote, and Transformer


Related Articles